Dreams-hop Woodworks

Welcome to

Dreams-hop Woodworks

Woodworcking Tools and Advice

5 Must-Have Power Tools For A Woodworking Business

If you want to set up your own woodworking business, there is no need to spend a lot at the beginning. You will need some basic power tools that will serve all the purpose of woodworking.

The woodworking business owners can make a choice between consumer grade and industrial grade power tools according to their workload. The consumer grade tools are cheaper in comparison to industrial grade but they fail with rigorous use. It is recommended to use consumer grade tools till your business gain a pace and after that to buy more powerful equipment.

The 5 great power tools for a woodworking business are listed below.


A Wood planer is a woodworking power tool used for producing boards of even thickness. They have an added advantage over the traditional planer. They feature a planning platform to adjust thickness very quickly. These ones can be used to level the thickness of irregular pieces of wood according to the project requirement. Thus, no need to worry about the thickness of wood while buying. See a list of the best wood planers.



The router really set up the standard for a woodworking business. It is used to make complex cuts and trimmings like dovetail joints and bevelling edges that otherwise takes a number of working hours. It can do more than fancy cuts. A master carpenter can utilize its ability to cut flawless patterns on the wood pieces. A powerful router will pay itself off very soon.

Table Saw


The table saw tops the list for any woodworking business. It is the instrument which is needed from the start of the project until the end and it is really versatile. The table saw which will complete all the major cuttings. The business owners are recommended to set a good budget for this primary tool. It is an important equipment to make complex cuts at the same angle, making slots and to speed up your project.

Belt and Orbital Sander

A wood project cannot be considered complete without sanding. This is not the limitation of use of a belt and orbital sander. A power tool like this can be used to take out a lot of wood. They are used to give smooth circular shapes, rounding the corners and shaping the edges. They can also be used to smoothen out the wood before or after the project.

Electric drill

Drilling is required at many stages while working with wood. An electric drill is available in different variants.

How to Use a Wood Jointer Machine

Many tools are available for various purposes. In woodworking, the purpose of a woodworking machine is for the creation of smooth and flat surfaces in a piece of wood along its four edges. However, you cannot be able to use the machine if you do not understand its functionality and how to use it. Here are some of the guidelines on how to use the machine.

Know the Machine


It is critical to understand the machine before using it. There are convenient features provided by most jointers that help in making the jointing process more predictable. It is important that you know proper adjustment of the fence, how to set the depth of cut, changing of blades, tensioning of the drive belt among other tasks involved in optimizing the functionality of the machine.

Coplanar Tables


A jointer needs to be properly tuned. Best straight edges should be used to make sure that there is the parallel setting of the tables. It is important that you refer to your manual for guidance when making necessary adjustments.

Fence Setting

You need to use a machinist’s square to perfectly set the fence in a square position. Digital angle gauge can be used as well. You also need to understand the limitations of your stock. The capacity boundaries of your jointer will be limited by the width and the length of its bed. You, therefore, need to set a lower limit on the board size for safety reasons.

Jointer Upper Limits

The length of your board should be limited not to exceed twice your infeed table length. You can test this by setting the board on the infeed table and watch if it balances. If it does, then with proper technique you will be able to achieve a straight edge.

Depth of Cut

The depth of cut should be set in a manner that makes noticeable progress with each pass and should not burden the motor in the process. Often, making passes twice is considered right to remove enough stock for a production square edge that is perfect.

Source: https://routplanix.com/best-wood-planer-reviews/

Face Jointing

Face jointing is meant to provide face flat for the placing of jointers when edge jointing. Safety and quality problems can result if this step is skipped. These are just some of the important steps you need to follow to produce perfect edges on your boards in a consistent manner.